Water Based > 1H20AR1/D
HumiSeal® 1H2OAR1/D is a water-based acrylic conformal coating, suitable for most dip application methods. The coating contains a UV tracer for ease of inspection. HumiSeal® 1H2OAR1/D provides excellent moisture insulation resistance and can be chemically removed or soldered through for rework. HumiSeal® 1H2OAR1/D is IPC-CC-830 and RoHS Directive EU 2002/95/EC compliant, and recognized under UL File Number E105698.
Cleanliness of the substrate is of extreme importance for the successful application of a conformal coating. Surfaces must be free of moisture, dirt, wax, grease, flux residues and all other contaminants. Contamination under the coating will cause problems that may lead to assembly failures.
Waterborne coatings should not be placed directly on bare/untreated steel. Applying waterborne coatings when the Relative Humidity is > 80% will adversely affect coating uniformity and can cause poor adhesion.
When HumiSeal® 1H2OAR1/D is first applied it has a milky white appearance. As the film dries, the white colour fades until a clear, transparent film remains. The white colour aids the operator’s coverage inspection and the colour change serves as an indicator that the coating is dry to the touch. It is recommended that the coating be allowed to reach a tack-free condition before using heat to accelerate the cure process.
Dipping
The material has been formulated for dip application as supplied and requires no thinning. Thinning will reduce the application performance and increase curing time substantially and is not recommended. Because it is a water based coating, evaporation of HumiSeal® 1H2OAR1/D from the dip tank is very low. However, over a long period of time, the addition of a small amount of fresh HumiSeal® 1H2OAR1/S is beneficial, to replace the low level of coalescing solvents that are lost along with some water. The coalescing solvents are essential to provide optimum film formation and the other physical and electrical properties of the resin.
A slightly slower immersion speed is recommended to reduce the possibility of air entrapment under the components. The withdrawal speed depends on the complexity of the assembly being coated. Although the material has been formulated to lay down 1.5 mils in a single dip application, for densely populated assemblies, reducing the withdrawal speed or applying two successive thinner coatings will give better edge coverage and a better coating appearance.
Product Specification
| Product Specification | |
| Density, per ASTM D1475 | 1.06 ± 0.03 g/cm³ |
| Solids Content, % by weight per Fed-Std-141, Meth. 4044 | 37 ± 2 % |
| Viscosity, per Fed-Std-141, Meth. 4287 | 750 ± 250 centipoise |
| Recommended Coating Thickness | 25 - 75 microns |
| Drying Time to Handle per Fed-Std-141, Meth. 4061 | 30 min |
| Recommended Curing Conditions | 1 hr @ RT and 6 hrs @ 80°C |
| Time required to Reach Optimum Properties | 7 days |
| Recommended Stripper | HumiSeal Stripper 1072 |
| Shelf Life at Room Temperature, DOM | 18 months |
| Thermal Shock, 50 cycles per MIL-I-46058C | -65°C to 125°C |
| Flammability, per UL94 | V-0 |
| Dielectric Withstand Voltage, per MIL-I-46058C | >1500 volts |
| Dielectric Breakdown Voltage, per ASTM D149 | 7925 volts |
| Dielectric Constant, at 1MHz and 25°C per ASTM D150-98 | 2.5 |
| Dissipation Factor, at 1MHz and 25°C per ASTM D150-98 | 0.01 |
| Insulation Resistance, per MIL-I-46058C | 2.1 x 1013 ohms (21TΩ) |
| Moisture Insulation Resistance, per MIL-I-46058C | 3.2 x 1010 ohms (32GΩ) |
| Fungus Resistance, per ASTM G21 | Passes |
Downloads
Datasheets
1H20AR1/D TDS (.pdf)
MSDS
1H20AR1/D MSDS - English (.pdf)
1H20AR1/D MSDS - French (.pdf)
1H20AR1/D MSDS - German (.pdf)
1H20AR1/D MSDS - Italian (.pdf)
1H20AR1/D MSDS - USA (.pdf)
1H2OAR1 Aerosol MSDS - USA (.pdf)
REACH
REACH Statement (.pdf)
Conformal Coating Standards
Disclaimer
All values contained herein are typical values.
Please consult the Technical Data Sheet for the specific product to obtain complete information and detailed specification ranges and physical properties
Use our Product Selector
Selecting the correct conformal coating for your application is often confusing and difficult with many factors to be considered.
We understand this and have created an intuitive Product Selector Guide to help you through the specification process.
